Edit · Filters 9 min

Filters that preview on the canvas

The Filter menu covers blur, sharpen, noise, and distortions such as Twirl and Wave, plus pixelate, stylize, and render. The dialog previews on the canvas while you move the controls.

Watch the change before you commit

If a selection is active, the filter changes only that area. To keep the filter editable, run it on a smart object. You can then change it, hide it, or remove it. Filter, then Liquify, pushes pixels by hand. The chord is Ctrl+Shift+X. On a Mac, Ctrl is Command. These steps are from the workflows guide, checked 21 November 2026. The selection underneath a filter is Select the part you mean.

Where the workflows guide puts the common filter jobs.
JobWhere
Blur, sharpen, noise, distort, pixelate, stylize, renderThe Filter menu. The dialog previews on the canvas.
Push pixels by handFilter, then Liquify. Ctrl+Shift+X.
A filter you can still edit laterRun it on a smart object.
Only part of the layerMake a selection first. The filter stays inside it.

A Photoshop plug-in does not load

PhotoCraft does not run Photoshop plug-ins, and it has no Extensions menu. It runs filters written as WebAssembly, the same file on every system. Installed filters appear in Filter, then Plug-ins. Install Plug-in is in that same menu. To load a folder of them each time PhotoCraft starts, use Edit, then Preferences, then Plugins. On a Mac, preferences are PhotoCraft, then Settings.

Plug-in compatibility is one of the gaps named in the README status note. That warning is What early alpha means.

A filter on pixels is harder to undo after you save

History can step back before you save. After the save, a filter baked into pixels is part of the layer. An adjustment you can still switch off lives in the stack from Layers, masks, and adjustments. The picture you send someone is still the flat copy in Send a flat picture and keep the layers.

A filter, an adjustment, and Liquify are different promises

The Filter menu is blur, sharpen, noise, distortions such as Twirl and Wave, pixelate, stylize, and render. The dialog previews on the canvas while you move the controls. If marching ants are up, only that area changes. Deselect first when the whole layer should move. An adjustment layer, by contrast, sits above the pixels and can be switched off next week. Image, then Adjustments, bakes a tonal change into the layer. Use a filter when you want blur, sharpen, noise, or a distortion. Use an adjustment layer when you want the tone reversible. The adjustment names are Layers, masks, and adjustments. The selection that limits a filter is Select the part you mean.

Liquify, Filter, then Liquify, or Ctrl+Shift+X, pushes pixels by hand. It is not a mask and it is not an adjustment layer. On a smart object the filter stays editable: you can change it, hide it, or remove it later. On ordinary pixels, History can step back until you save. After the save, a baked filter is part of the layer. Run the risky one on a duplicate layer, Ctrl+J, or on a smart object. The flat picture you send is still Send a flat picture and keep the layers, and it should not be the only file you kept.

You can combine the two limits. Make the selection first, then run the filter on a smart object, and the change stays inside the ants while the filter itself can still be reopened. Cancel the dialog if the preview is wrong. OK writes it. Blur, sharpen, and noise are the repair group. Pixelate, stylize, and the named distortions Twirl and Wave are looks. Render is its own group on that menu. None of them are a substitute for an adjustment layer when the job is only brightness or hue. If the preview is slow, check the status bar for CPU Rendering before you decide the filter is broken. That status is When the window closes or the canvas is slow.

Extra filters are WebAssembly, loaded on purpose

PhotoCraft does not run Photoshop plug-in files, and it has no Extensions menu. Filters you add are WebAssembly, the same file on every system. They appear under Filter, then Plug-ins. Install Plug-in is in that menu. Edit, then Preferences, then Plugins, points at a folder PhotoCraft loads each time it starts. On a Mac the preferences menu is PhotoCraft, then Settings. A folder of .8bf files will not become that list. Plug-in compatibility is a gap the README names, so a studio action that depends on a commercial plug-in is outside this alpha. That boundary is What early alpha means.

Preview at 100 percent before OK. A halo that the fit-on-screen view hides is still in the file after you save. The workflows guide checked 21 November 2026 is the source for the menu names on this page, already linked in the first section. If the canvas is on CPU Rendering, filters still run, and they run slower. The switch back to the graphics card is When the window closes or the canvas is slow.